Product description

    The Pressac sensing mini series door and window sensor is a contact sensor that can sense when a door or window is opened or closed. The door and window sensor offers quick and versatile installation via adhesive film or screws. Once triggered the door and window sensor can activate a wide variety of potential responses.

    Key features and benefits

    • Energy harvesting – powered by ambient light from the surrounding environment
    • Battery variation, for robust operation in dark environments
    • No wiring required – low cost of installation
    • Fast installation time – minimal disruption for retro fits

    Available variants

    Frequency Type Frequency Type Part Number
    868MHz Solar only EnOcean for Europe MS_DOOR_WIN_SLR_868
    868MHz Solar with battery back-up EnOcean for Europe MS_DOOR_WIN_BAT_868
    902MHz Solar only EnOcean for USA/Canada MS_DOOR_WIN_SLR_902
    902MHz Solar with battery back-up EnOcean for USA/Canada MS_DOOR_WIN_BAT_902
    928MHz Solar only EnOcean for Japan MS_DOOR_WIN_SLR_928
    928MHz Solar with battery back-up EnOcean for Japan MS_DOOR_WIN_BAT_928

    Installation

    Installation of the mini series door and window sensor can be done using the adhesive pads or screws provided.

    NOTE: The mini series door and window sensor and the magnet should be no further than 5mm apart.

    Adhesive pads installation

    1. Ensure the surface is clean and dry. Use the supplied alcohol wipe to prepare the surface if required.
    2. Stick the supplied self-adhesive pads to the bottom of the mini series door and window sensor and magnet.
    3. Peel off the self-adhesive pad’s protective film.
    4. Stick the mini series door and window sensor close to the edge of the door or window frame without hanging over. Ensure the solar panel gets as much light as possible.
    5. Attach the magnet to the moving part of the door or window.

    Installation using screws

    1. Remove the screw from the side of the unit and lift the mini series door and window sensor from its backplate.
    2. Using the screws provided, screw the mini series door and window sensor backplate close to the edge of the door or window frame without hanging over. Ensure the solar panel gets as much light as possible.
    3. Place the mini series door and window sensor onto the backplate.
    4. Replace the screw into the side of the unit and securely tighten.
    5. Attach the magnet to the moving part of the door or window.

    Changing the battery

    Estimated battery life using default settings assuming average use can be found in the technical specification section of this document. Changing the battery in the mini series door and window sensor can be done by following the steps below.

    1. Remove the screw from the side of the unit and lift the sensor from its backplate.
    2. Unplug the connected daughter board by gently lifting upwards.
    3. Replace the battery in the battery holder.
    4. Plug the daughter board back into the main board.
    5. Place the sensor onto the backplate.
    6. Replace the screw into the side of the unit and securely tighten.

    Activation

    Solar powered with battery back-up

    Mini series door and window sensors equipped with a battery back-up require turning on prior to first use. You can do this by opening the back cover and sliding the switch to the ‘on’ position.

    Solar powered only

    Prior to first use, the sensor requires its power reserve charging. You can do this by placing the sensor in illuminance of at least 200lux for a minimum of five minutes.

    Secure mode

    The mini series door and window sensor includes an enhanced secure mode. When secure mode is turned on all device communication is encrypted by AES128. For more information, EnOcean’s full security specification can be found at https://www.enocean.com

    Switching between modes

    NOTE: Before changing the mini series door and window sensor’s operating mode please make sure the device is removed from all receiving devices it has been configured to work with. Failure to do so could result in ignored telegrams.

    The sensor can be switched between standard mode and secure mode by pressing the learn button for five seconds, releasing for one second and then pressing again for five seconds. The device will send a secure learn telegram and the LED will flash twice when successful.

    • Secure mode activation is indicated by the LED flashing twice.
    • Standard mode activation is indicated by the LED flashing once.

    The mini series door and window sensor is delivered in transport mode with encryption turned off.

    Commissioning

    Adding the EnOcean mini series door and window sensor to an EnOcean radio network.

    NOTE: If including a mini series door and window sensor in secure mode please ensure your receiving device is EnOcean security compatible.

    1. Ensure your sensor is within range of your EnOcean gateway or receiving device.
    2. Place your EnOcean gateway or receiving device into inclusion mode.
    3. Press the Learn button on the back of the sensor. The LED will blink once. The device will now transmit a teach in telegram.
    4. Wait for the teach in process to end. Please allow extra time if using secure mode.
    5. Successful inclusion will be indicated on the EnOcean gateway or receiving device.

    The mini series door and window sensor can also be included into your EnOcean network manually. This can be achieved using the unique EnOcean ID and the EnOcean Equipment Profile (EEP). The EnOcean ID and EEP are printed on the product label.

    Technical specifications

    Wireless protocol EnOcean
    Measurement range Reports open/close
    Transmission rate (dynamic) Instant on open/close else every 15 minutes
    Battery life* (battery back-up only) Up to 10 Years
    Battery type (battery back-up only) CR2354
    Repeater No
    Telegram 1BS
    Environment Indoor
    Enclosure material PC-ABS
    Calibration Factory calibrated
    Operating temperature range -20ºC to +60ºC
    Storage temperature range -20ºC to +60ºC
    Dimensions 76.5mm x 28mm x 17.5mm approx
    EEP D5-00-01

    *Typical life expectancy of the battery back-up is dependent on ambient light conditions and use-case.

    Declaration of conformity

    Download product datasheet

     

    in Pressac sensors