Product description

    A fully wireless, compact sensor to measure ambient temperature and relative humidity. The Pressac Sensing Mini Series Temperature and Humidity Sensor allows efficient monitoring and optimisation of indoor climates in buildings. The sensor provides true peel and stick deployment, comes in two variations requiring little to no maintenance and can be rapidly fitted at minimal cost.

    Key features and benefits

    • Energy harvesting – powered by ambient light from the surrounding environment
    • Battery variation, for robust operation in dark environments
    • No wiring required – low cost of installation
    • Fast installation time – minimal disruption for retro fits
    • Optimal positioning – no wiring constraints

    Available variants

    Frequency Type Frequency Type Part Number
    868MHz Solar only EnOcean for Europe MS_TEMP_HUM_SLR_868
    868MHz Solar with battery back-up EnOcean for Europe MS_TEMP_HUM_BAT_868
    902MHz Solar only EnOcean for USA/Canada MS_TEMP_HUM_SLR_902
    902MHz Solar with battery back-up EnOcean for USA/Canada MS_TEMP_HUM_BAT_902
    928MHz Solar only EnOcean for Japan MS_TEMP_HUM_SLR_928
    928MHz Solar with battery back-up EnOcean for Japan MS_TEMP_HUM_BAT_928

    Installation

    Place the sensor in an area of average room temperature keeping away from radiators, windows, ventilation units, cooling systems and any excess air movement. Ensure the solar panel gets as much light as possible.

    NOTE: Installing the mini series temperature and humidity sensor on the inside of an outside wall or directly over pipe work concealed in walls may negatively impact temperature measurement.

    Once you have identified your desired surface, installation can be done using the adhesive pads or screws provided.

    Adhesive pads installation

    1. Ensure the surface is clean and dry. Use the supplied alcohol wipe to prepare the surface if required.
    2. Stick the supplied self-adhesive pads to the bottom of the sensor.
    3. Peel off the self-adhesive pad’s protection film.
    4. Carefully stick the sensor to the desired surface.

    Installation using screws

    1. Remove the screw from the side of the unit and lift the sensor from its backplate.
    2. Using the screws provided, screw the sensor’s backplate to the desired surface.
    3. Place the sensor onto the backplate.
    4. Replace the screw into the side of the unit and securely tighten.

    Changing the battery

    Estimated battery life using default settings assuming average use can be found in the technical specification section of this document. Changing the battery in the mini series temperature sensor can be done by following the steps below.

    1. Remove the screw from the side of the unit and lift the sensor from its backplate.
    2. Unplug the connected daughter board by gently lifting upwards.
    3. Replace the battery in the battery holder.
    4. Plug the daughter board back into the main board.
    5. Place the sensor onto the backplate.
    6. Replace the screw into the side of the unit and securely tighten.

    Activation

    The mini series temperature and humidity sensor will be shipped in transport mode. Transport mode turns off the radio module during transit to reduce battery consumption, no telegrams will be sent while this is active. This mode can be changed by pressing the learn button and following the below procedures.

    • Change from transport to standard mode
      After pressing the learn button for one second then releasing, the sensor will enter standard mode. The device will send a standard learn telegram and the LED will flash once when successful.
    • Change from secure or standard to transport mode
      After pressing the learn button for five seconds then releasing, the sensor will enter transport mode. The device will send a secure telegram and the LED will flash three times when successful.

    Solar powered with battery back-up

    Mini series temperature and humidity sensors equipped with a battery back-up require turning on prior to first use. You can do this by opening the back cover and sliding the switch to the ‘on’ position.

    Solar powered only

    Prior to first use, the sensor requires its power reserve charging. You can do this by placing the sensor in illuminance of at least 200lux for a minimum of five minutes.

    Secure mode

    The mini series temperature and humidity sensor includes an enhanced secure mode. When secure mode is turned on all device communication is encrypted by AES128. For more information, EnOcean’s full security specification can be found at https://www.enocean.com

    Switching between modes

    NOTE: Before changing the mini series temperature and humidity sensor’s operating mode please make sure the device is removed from all receiving devices it has been configured to work with. Failure to do so could result in ignored telegrams.

    The sensor can be switched between standard mode and secure mode by pressing the learn button for five seconds, releasing for one second and then pressing again for five seconds. The device will send a secure learn telegram and the LED will flash twice when successful.

    The mini series temperature and humidity sensor is delivered in transport mode with encryption turned off.

    Commissioning

    Adding the EnOcean mini series temperature and humidity sensor to an EnOcean radio network.

    NOTE: If including a mini series temperature and humidity sensor in secure mode please ensure your receiving device is EnOcean security compatible.

    1. Ensure your sensor is within range of your EnOcean gateway or receiving device.
    2. Place your EnOcean gateway or receiving device into inclusion mode.
    3. Press the Learn button on the back of the sensor. The LED will blink once. The device will now transmit a teach in telegram.
    4. Wait for the teach in process to end. Please allow extra time if using secure mode.
    5. Successful inclusion will be indicated on the EnOcean gateway or receiving device.

    The mini series temperature and humidity sensor can also be included into your EnOcean network manually. This can be achieved using the unique EnOcean ID and the EnOcean Equipment Profile (EEP). The EnOcean ID and EEP are printed on the product label.

    Technical specifications

    Wireless protocol EnOcean
    Measurement range Temperature 0ºC to 40ºC
    Humidity 0%R.H. to 100%R.H.
    Accuracy +/-0.5ºC between 17°C and 27°C
    +/- 1°C between 0°C and 17°C
    +/- 1°C between 27°C and 40°C
    +/-5% R.H. Between 30% – 70% R.H. 0-40°C
    Transmission rate (dynamic) 100 seconds if temperature change > 0.5°C
    or humidity change > 2%
    else every 15 minutes
    Battery life* (battery back-up only) Up to 10 Years
    Battery type (battery back-up only) CR2354
    Repeater No
    Telegram 4BS
    Environment Indoor
    Enclosure material PC-ABS
    Calibration Factory Calibrated
    Operating temperature range -20ºC to +60ºC
    Storage temperature range -20ºC to +60ºC
    Dimensions 76.5mm x 28mm x 17.5mm approx
    EEP A5-04-01

    *Typical life expectancy of the battery is dependent on ambient light conditions and use-case.

    Declaration Of Conformity

    Download product datasheet

    in Pressac sensors